Bsi bs en 60794 2 31 2013

BSI Standards PublicationOptical fibre cables Part 2-31: Indoor optical fibre cables — Detailed specification for optical fibre ribbon cables for use in premises cabling BS EN 60794-2-31

BSI Standards Publication

Optical fibre cables

Part 2-31: Indoor optical fibre cables — Detailed specification for optical fibre ribbon cables for use in premises cabling

BS EN 60794-2-31:2013

National foreword

This British Standard is the UK implementation of EN 60794-2-31:2013 It is identical to IEC 60794-2-31:2012 It supersedes BS EN 60794-2-31:2006 which is withdrawn

The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/1, Optical fibres and cables

A list of organizations represented on this committee can be obtained on request to its secretary

This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application

© The British Standards Institution 2013 Published by BSI Standards Limited 2013 ISBN 978 0 580 71601 0

ICS 33.180.10

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2013

Amendments issued since publication

Amd No Date Text affected

BRITISH STANDARD

BS EN 60794-2-31:2013

NORME EUROPÉENNE

CENELEC

European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members

Ref No EN 60794-2-31:2013 E

English version

Optical fibre cables - Part 2-31: Indoor cables - Detailed specification for optical fibre ribbon cables for use in premises

cabling

(IEC 60794-2-31:2012)

Câbles à fibres optiques -

Partie 2-31: Câbles intérieurs -

Spécification particulière pour les câbles à

fibres optiques en ruban utilisés dans le

câblage de locaux

(CEI 60794-2-31:2012)

Lichtwellenleiterkabel - Teil 2-31: LWL-Innenkabel - Bauartspezifikation für LWL-Bandkabel zur Innenverlegung für

anwendungsneutrale Standortverkabelung (IEC 60794-2-31:2012)

This European Standard was approved by CENELEC on 2012-12-12 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member

This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified

to the CEN-CENELEC Management Centre has the same status as the official versions

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom

EN 60794-2-31:2013 - 2 -

Foreword

The text of document 86A/1468/FDIS, future edition 2 of IEC 60794-2-31, prepared by SC 86A, "Fibres and cables", of IEC TC 86, "Fibre optics" was submitted to the IEC-CENELEC parallel vote and approved

by CENELEC as EN 60794-2-31:2013

The following dates are fixed:

• latest date by which the document has

to be implemented at national level by

publication of an identical national

standard or by endorsement

(dop) 2013-09-12

• latest date by which the national

standards conflicting with the

document have to be withdrawn

(dow) 2015-12-12

This document supersedes EN 60794-2-31:2006

EN 31:2013 includes the following significant technical changes with respect to EN 60794-2-31:2006:

• incorporation of the OM4 cabled fibre performance category;

• incorporation of the OS2 cabled fibre performance category;

• incorporation of the B6_a1 and B6_a2 fibre categories as per EN 60793-2-50

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights

Endorsement notice

The text of the International Standard IEC 60794-2-31:2012 was approved by CENELEC as a European Standard without any modification

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60794-1-1 NOTE Harmonized as EN 60794-1-1

IEC 60794-2 NOTE Harmonized as EN 60794-2

BS EN 60794-2-31:2013

- 3 - EN 60794-2-31:2013

Annex ZA

(normative)

Normative references to international publications with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies

NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies

To be used together with the Annexes ZA of EN 60794-1-1, EN 60794-1-2, EN 60794-2 and EN

60794-2-30

IEC 60793-2-10 2011 Optical fibres -

Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres

EN 60793-2-10 2011

IEC 60793-2-50 2008 Optical fibres -

Part 2-50: Product specifications - Sectional specification for class B single-mode fibres

EN 60793-2-50 2008

IEC 60794-1-2 - Optical fibre cables -

Part 1-2: Generic specification - Basic optical cable test procedures

EN 60794-1-2 -

IEC 60794-2-30 2008 Optical fibre cables -

Part 2-30: Indoor cables - Family specification for ribbon cables

EN 60794-2-30 2008

ISO/IEC 11801 - Information technology - Generic cabling for

– 2 – 60794-2-31 © IEC:2012

CONTENTS

1 Scope 5

2 Normative references 5

3 General requirements 5

4 Particular requirements 6

Temperature cycling 6

4.1 Transmission requirements 6

4.2 Attenuation of cabled fibre 6

4.2.1 Fibre bandwidth requirements 7

4.2.2 Bibliography 8

Table 1 – Multimode maximum cable attenuation coefficient (dB/km) 6

Table 2 – Single-mode maximum cable attenuation coefficient (dB/km) 7

Table 3 – Minimum multimode fibre bandwidth (MHz×km) 7

BS EN 60794-2-31:2013

60794-2-31 © IEC:2012 – 5 –

OPTICAL FIBRE CABLES – Part 2-31: Indoor cables – Detailed specification for optical fibre ribbon cables

for use in premises cabling

1 Scope

This part of the IEC 60794 series presents the detailed requirements specific to indoor optical fibre ribbon cables to ensure compatibility with ISO/IEC 11801 The requirements of the family specification IEC 60794-2-30 are applicable to cables covered by this standard

The particular requirements detailed in Clause 4 either define a specific option relative to the requirements of IEC 60794-2-30 or define additional requirements

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies

NOTE They complete the normative references already listed in the generic specification (IEC 60794-1-1[1] 1 and IEC 60794-1-2) and in the sectional specification (IEC 60794-2 [2]) or in the family specification (IEC 60794-2-30)

IEC 60793-2-10:2011, Optical fibres − Part 2-10: Product specifications − Sectional specification for category A1 multimode fibres

IEC 60793-2-50:2008, Optical fibres − Part 2-50: Product specifications − Sectional specification for class B single-mode fibres

IEC 60794-1-2, Optical fibre cables – Part 1-2: Generic specification – Basic optical cable test

procedures

IEC 60794-2-30:2008, Optical fibre cables − Part 2-30: Indoor cables − Family specification for ribbon cables

ISO/IEC 11801, Information technology − Generic cabling for customers premises

3 General requirements

The cable shall comply with the family specification (IEC 60794-2-30) and meet the requirements that are defined in it

The optical fibre contained in the cables which are covered by this standard shall comply with one of the following standards and meet the normative requirements defined within them as applicable:

• IEC 60793-2-50:2008, Annex A (Single-mode B1.1 fibre)

—————————

1 Numbers in square brackets refer to the Bibliography

– 6 – 60794-2-31 © IEC:2012

• IEC 60793-2-50:2008, Annex C (Single-mode B1.3 fibre)

• IEC 60793-2-50:2008, Annex G (Single-mode B6_a1 and B6_a2 fibre)

• IEC 60793-2-10:2011, Annex A (Multimode A1a.1, 50 µm core fibre)

• IEC 60793-2-10:2011, Annex A (Multimode A1a.2, 50 µm core fibre)

• IEC 60793-2-10:2011, Annex A (Multimode A1a.3, 50 µm core fibre)

• IEC 60793-2-10:2011, Annex B (Multimode A1b, 62,5 µm core fibre)

To ensure compatibility with ISO/IEC 11801, optical performance level requirements are presented in terms of the performance classification codes for cabled optical fibre as follows:

• OS1 Single-mode fibre, categories B1.1, B1.3 or sub-categories B6_a1 and B6_a2;

• OS2 Single-mode fibre, category B1.3 or sub-categories B6_a1 and B6_a2

• OM1 Multimode fibre, model A1a.1 or sub-category;A1b

• OM2 Multimode fibre, model A1a.1 or sub-category;A1b;

• OM3 Multimode fibre, model A1a.2;

• OM4 Multimode fibre, model A1a.3

NOTE These codes are informative from the perspective of the requirements defined in this detailed specification

4 Particular requirements

Temperature cycling

4.1

The cable shall meet the requirement of IEC 60794-2-30:2008, Table 2, Option c (–20 °C to +60 °C)

The test shall be performed on a 50 m specimen

No attenuation changes shall be allowed during the test (see IEC 60794-1-2 for definition of

“no change in attenuation)

Transmission requirements

4.2

Attenuation of cabled fibre

4.2.1

Depending on the fibre category, the attenuation coefficient of the cabled fibre shall be less than the maximum values in Table 1 for the multimode fibres and less than the maximum values in Table 2 for single-mode fibres – for the wavelengths listed in the table

The fibre category shall be agreed between customer and supplier

Table 1 – Multimode maximum cable attenuation coefficient (dB/km)

IEC 60793-2-10, A1a.1 3,5 1,5 OM1 OM2

IEC 60793-2-10, A1a.2 3,5 1,5 OM1 OM2 OM3 IEC 60793-2-10, A1a.3 3,5 1,5 OM1 OM2 OM3 OM4 IEC 60793-2-10, A1b 3,5 1,5 OM1 OM2

BS EN 60794-2-31:2013

60794-2-31 © IEC:2012 – 7 –

Table 2 – Single-mode maximum cable attenuation coefficient (dB/km)

IEC 60793-2-50, B1.1,

B1.3 ,B6_a1 , B6_a2 1 310, 1 550 1,0 OS1

IEC 60793-2-50, B1.3,

B6_a1, B6_a2 1 310, 1 383, 1 550 0,4 OS2

Fibre bandwidth requirements

4.2.2

There are no bandwidth requirements on single-mode fibre

For cables containing multimode fibres, the uncabled fibre shall be specified at one of the performance levels defined in Table 3 in terms of minimum bandwidth (MHz × km), wavelength, and type of measurement

The fibre category and performance level shall be agreed between customer and supplier

Table 3 – Minimum multimode fibre bandwidth (MHz×km)

diameter

µm

Overfilled bandwidth at

850 nm

Overfilled bandwidth at

1 300 nm

Effective modal bandwidth at

850 nm

Performance codes

IEC 60793-2-10, A1a.1 50 200 500 na OM1 IEC 60793-2-10, A1a.1 50 500 500 na OM2 IEC 60793-2-10, A1a.2 50 1 500 500 2 000 OM3 IEC 60793-2-10, A1a.3 50 3 500 500 4 700 OM4 IEC 60793-2-10, A1b 62,5 200 500 na OM1 IEC 60793-2-10, A1b 62,5 500 500 na OM2

– 8 – 60794-2-31 © IEC:2012 Bibliography

IEC 60794-1-1, Optical fibre cables – Part 1-1: Generic specification – General

IEC 60794-2, Optical fibre cables – Part 2: Indoor cables – Sectional specification

_

BS EN 60794-2-31:2013

BSI is the national body responsible for preparing British Standards and other

standards-related publications, information and services.

BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited.

British Standards Institution (BSI)

BSI Group Headquarters

389 Chiswick High Road London W4 4AL UK

About us

We bring together business, industry, government, consumers, innovators

and others to shape their combined experience and expertise into standards

-based solutions.

The knowledge embodied in our standards has been carefully assembled in

a dependable format and refined through our open consultation process

Organizations of all sizes and across all sectors choose standards to help

them achieve their goals.

Information on standards

We can provide you with the knowledge that your organization needs

to succeed Find out more about British Standards by visiting our website at

bsigroup.com/standards or contacting our Customer Services team or

Knowledge Centre.

Buying standards

You can buy and download PDF versions of BSI publications, including British

and adopted European and international standards, through our website at

bsigroup.com/shop, where hard copies can also be purchased

If you need international and foreign standards from other Standards Development

Organizations, hard copies can be ordered from our Customer Services team.

Subscriptions

Our range of subscription services are designed to make using standards

easier for you For further information on our subscription products go to

bsigroup.com/subscriptions.

With British Standards Online (BSOL) you’ll have instant access to over 55,000

British and adopted European and international standards from your desktop

It’s available 24/7 and is refreshed daily so you’ll always be up to date

You can keep in touch with standards developments and receive substantial

discounts on the purchase price of standards, both in single copy and subscription

format, by becoming a BSI Subscribing Member

PLUS is an updating service exclusive to BSI Subscribing Members You will

automatically receive the latest hard copy of your standards when they’re

revised or replaced

To find out more about becoming a BSI Subscribing Member and the benefits

of membership, please visit bsigroup.com/shop.

With a Multi-User Network Licence (MUNL) you are able to host standards

publications on your intranet Licences can cover as few or as many users as you

wish With updates supplied as soon as they’re available, you can be sure your

documentation is current For further information, email bsmusales@bsigroup.com.

Revisions

Our British Standards and other publications are updated by amendment or revision

We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.

Copyright

All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person

or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system

or transmitted in any form or by any means – electronic, photocopying, recording

or otherwise – without prior written permission from BSI Details and advice can

be obtained from the Copyright & Licensing Department.

Useful Contacts:

Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions

Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre

Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing

Tel: +44 20 8996 7070 Email: copyright@bsigroup.com

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW