Bsi bs en 60819 1 2012

Aramid paper may contain materials with or without the addition of suitable organic and/or inorganic filler and/or binder materials.. 2.2 polyethylene paper wet-laid, non-woven paper m

Trang 1

BSI Standards Publication

Non-cellulosic papers for electrical purposes

Part 1: Definitions and general requirements

BS EN 60819-1:2012

Trang 2

National foreword

This British Standard is the UK implementation of EN 60819-1:2012 It is identical to IEC 60819-1:2009 It supersedes BS EN 60819-1:1996, which will

be withdrawn on 14 February 2015

The UK participation in its preparation was entrusted to Technical Committee GEL/15, Solid electrical insulating materials

A list of organizations represented on this committee can be obtained

on request to its secretary

This publication does not purport to include all the necessary provisions of

a contract Users are responsible for its correct application

ICS 01.040.29; 29.035.10

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Stand-ards Policy and Strategy Committee on 31 August 2012

Amendments issued since publication

Date Text affected

BRITISH STANDARD

BS EN 60819-1:2012

Trang 3

NORME EUROPÉENNE

CENELEC

European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

Ref No EN 60819-1:2012 E

English version

Non-cellulosic papers for electrical purposes - Part 1: Definitions and general requirements

(IEC 60819-1:2009)

Papiers non cellulosiques à usages

électriques -

Partie 1: Définitions et exigences

générales

(CEI 60819-1:2009)

Vliesstoffe auf Kunststofffaserbasis für elektrotechnische Zwecke -

Teil 1: Begriffe und allgemeine Anforderungen

(IEC 60819-1:2009)

This European Standard was approved by CENELEC on 2012-02-14 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member

This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified

to the CEN-CENELEC Management Centre has the same status as the official versions

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom

BS EN 60819-1:2012

Trang 4

EN 60819-1:2012 - 2 -

Foreword

This document (EN 60819-1:2012) consists of the text of IEC 60819-1:2009 prepared by IEC/TC 15

"Solid electrical insulating materials"

The following dates are fixed:

• latest date by which the document has

to be implemented at national level by

publication of an identical national

standard or by endorsement

(dop) 2012-11-14

• latest date by which the national

standards conflicting with the

document have to be withdrawn

(dow) 2015-02-14

This document supersedes EN 60819-1:1995 + A1:1996

EN 60819-1:2012 includes the following significant technical changes with respect to EN 60819-1:1995: The list of materials to be used in combination was updated with the addition of new materials made available by progress in technology and described in Subclauses 2.7 and 2.8

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights

Endorsement notice

The text of the International Standard IEC 60819-1:2009 was approved by CENELEC as a European Standard without any modification

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60819-3-1 NOTE Harmonized as EN 60819-3-1

BS EN 60819-1:2012

Trang 5

– 4 – 60819-1 © IEC:2009

INTRODUCTION

This International Standard forms an element of a series which deals with non-cellulosic papers for electrical purposes

The series consists of three parts:

Part 1: Definitions and general requirements (IEC 60819-1)

Part 2: Methods of test (IEC 60819-2)

Part 3: Specifications for individual materials (IEC 60819-3)

BS EN 60819-1:2012

Trang 6

60819-1 © IEC:2009 – 5 –

NON-CELLULOSIC PAPERS FOR ELECTRICAL PURPOSES –

Part 1: Definitions and general requirements

1 Scope

This part of IEC 60819 gives the definitions and general requirements for non-cellulosic papers for electrical purposes

Materials which conform to this specification meet established levels of performance However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone

SAFETY WARNING

It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner

2 Terms and definitions

For the purpose of this document, the following definitions apply:

2.1

aramid (aromatic polyamide) paper

wet-laid, non-woven paper in which the fibres are synthetic aromatic polyamide having at least 85 % of the amide linkage attached directly to two aromatic rings Aramid paper may contain materials with or without the addition of suitable organic and/or inorganic filler and/or binder materials

2.2

polyethylene paper

wet-laid, non-woven paper made from specially prepared polyethylene (PE) fibres with or without the addition of suitable organic and/or inorganic filler and/or binder materials

2.3

polypropylene paper

wet-laid, non-woven paper made from specially prepared polypropylene fibres (PP) with or without the addition of suitable organic and/or inorganic filler and/or binder materials

2.4

glass paper

wet-laid, non-woven paper made from glass micro-fibres made with or without the addition of suitable organic and/or inorganic filler and/or binder materials In cases of poor fibre adhesion, the situation may be remedied by acid treatment to produce a slight gelation which will act as a binder, or by adding an inorganic binder

2.5

ceramic paper

wet-laid, non-woven paper made from ceramic fibres For examples, alumina-silica paper composed of approximately 51 % alumina (Al2O3) and 47 % silica (SiO2) Ceramic papers may be modified with or without the addition of suitable organic and/or inorganic filler and/or binder materials

BS EN 60819-1:2012

Trang 7

– 6 – 60819-1 © IEC:2009

2.6

poly(ethylene)-terephthalate paper

dry-laid fibre mat paper made from specially prepared polyethylene-terephthalate (PET) fibres with or without the addition of suitable organic and/or inorganic filler and/or binder materials

NOTE Polyethylene-terephthalate paper is sometimes erroneously called PETP paper

2.7

filled glass paper

paper in which at least 65 % of the raw material composition is glass fibres and inorganic fillers (such as silicate of aluminium) with or without the addition of other fibres and/or binder material

2.8

hybrid inorganic-organic paper

wet-laid, non-woven paper made from organic polymer fibres, such as Aramid or PET fibres and inorganic fillers, such as silicates of alumina with or without addition of other fibres and/or binder materials

3.1 All materials in any one consignment shall be consistent and have properties within the

limits of this standard throughout the whole sheet or throughout the whole length of each roll The surface shall be uniform, reasonably smooth and reasonably free from defects such as bubbles, pin holes, creases and flaws

3.2 When delivered in rolls, it shall be capable of being unrolled without damage

3.3 The combined materials shall be free of conducting particles and other undesirable

inclusions

3.4 Materials delivered in sheets cut to length shall be reasonably free from warp

4 Dimensions

Thickness and thickness tolerances are dealt with in the Sheets of the IEC 60819-3 series

Other dimensions and tolerances shall be agreed by the purchaser and the supplier

5 Joins

For material in roll form, the allowable frequency of joins, the details of their construction, and identification shall be agreed by the purchaser and the supplier

6 Conditions of supply

Material in roll form shall be supplied on cardboard roll or other suitable core The inner diameter of the core shall be agreed by purchaser and supplier, and it should preferably be,

76 mm or 152 mm

Material in sheet form shall be supplied in stacks

The paper shall be placed in a package which ensures adequate protection during transport, handling and storage

BS EN 60819-1:2012

Trang 8

60819-1 © IEC:2009 – 7 –

Each unit pack, and each package containing a number of unit packs, shall have the following information clearly and indelibly marked on it:

– reference to this standard;

– product type, in accordance with Clause 2;

– for materials delivered in rolls: the width and the length or mass of each roll;

– for materials delivered in sheets: the dimensions of the sheets and the number of sheets

in a stack or the mass of the stack;

– the nominal thickness of the material;

– the number of rolls or stacks in a larger package;

– information about joins;

– the nominal thickness of the paper;

This information shall be clearly marked on the outside of the package

BS EN 60819-1:2012

Trang 9

– 8 – 60819-1 © IEC:2009

Bibliography

IEC 60819-3-1, Non-cellulosic papers for electrical purposes – Part 3: Specification for

individual materials – Sheet 1: Filled glass paper

individual materials – Sheet 2: Hybrid inorganic-organic paper

individual materials – Sheet 3: Unfilled aramid (aromatic polyamide) papers

individual materials – Sheet 4: Aramid fibre paper containing not more than 50% of mica particles

_

BS EN 60819-1:2012

Trang 10

This page deliberately left blank

Trang 12

BSI is the national body responsible for preparing British Standards and other

standards-related publications, information and services.

BSI is incorporated by Royal Charter British Standards and other standardization products are published by BSI Standards Limited.

British Standards Institution (BSI)

BSI Group Headquarters

389 Chiswick High Road London W4 4AL UK

About us

We bring together business, industry, government, consumers, innovators

and others to shape their combined experience and expertise into standards

-based solutions.

The knowledge embodied in our standards has been carefully assembled in

a dependable format and refined through our open consultation process

Organizations of all sizes and across all sectors choose standards to help

them achieve their goals.

Information on standards

We can provide you with the knowledge that your organization needs

to succeed Find out more about British Standards by visiting our website at

bsigroup.com/standards or contacting our Customer Services team or

Knowledge Centre.

Buying standards

You can buy and download PDF versions of BSI publications, including British

and adopted European and international standards, through our website at

bsigroup.com/shop, where hard copies can also be purchased

If you need international and foreign standards from other Standards Development

Organizations, hard copies can be ordered from our Customer Services team.

Subscriptions

Our range of subscription services are designed to make using standards

easier for you For further information on our subscription products go to

bsigroup.com/subscriptions.

With British Standards Online (BSOL) you’ll have instant access to over 55,000

British and adopted European and international standards from your desktop

It’s available 24/7 and is refreshed daily so you’ll always be up to date

You can keep in touch with standards developments and receive substantial

discounts on the purchase price of standards, both in single copy and subscription

format, by becoming a BSI Subscribing Member

PLUS is an updating service exclusive to BSI Subscribing Members You will

automatically receive the latest hard copy of your standards when they’re

revised or replaced

To find out more about becoming a BSI Subscribing Member and the benefits

of membership, please visit bsigroup.com/shop.

With a Multi-User Network Licence (MUNL) you are able to host standards

publications on your intranet Licences can cover as few or as many users as you

wish With updates supplied as soon as they’re available, you can be sure your

documentation is current For further information, email bsmusales@bsigroup.com.

Revisions

Our British Standards and other publications are updated by amendment or revision

We continually improve the quality of our products and services to benefit your business If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.

Copyright

All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person

or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system

or transmitted in any form or by any means – electronic, photocopying, recording

or otherwise – without prior written permission from BSI Details and advice can

be obtained from the Copyright & Licensing Department.

Useful Contacts:

Customer Services Tel: +44 845 086 9001 Email (orders): orders@bsigroup.com Email (enquiries): cservices@bsigroup.com Subscriptions

Tel: +44 845 086 9001 Email: subscriptions@bsigroup.com Knowledge Centre

Tel: +44 20 8996 7004 Email: knowledgecentre@bsigroup.com Copyright & Licensing

Tel: +44 20 8996 7070 Email: copyright@bsigroup.com

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

Tiêu đề	Non-cellulosic papers for electrical purposes Part 1: Definitions and general requirements
Trường học	British Standards Institution
Chuyên ngành	Electrotechnical Standards
Thể loại	standards publication
Năm xuất bản	2012
Thành phố	London

Định dạng
Số trang	12
Dung lượng	0,99 MB