BS EN 6129:2016Aerospace series — Blind bolt, protruding head, high strength, pulltype BSI Standards Publication... This British Standard was published under the authority of the Standar
Trang 1BS EN 6129:2016
Aerospace series — Blind bolt, protruding head, high strength, pulltype
BSI Standards Publication
Trang 2This British Standard is the UK implementation of EN 6129:2016 The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems
A list of organizations represented on this committee can be obtained on request to its secretary
This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application
© The British Standards Institution 2016
Published by BSI Standards Limited 2016 ISBN 978 0 580 92623 5
ICS 49.030.20; 49.030.60
Compliance with a British Standard cannot confer immunity from legal obligations.
This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016
Amendments/corrigenda issued since publication
Trang 3BS EN 6129:2016
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2016
ICS 49.030.20; 49.030.60
English Version
Aerospace series - Blind bolt, protruding head, high
strength, pulltype
Série aérospatiale - Boulon aveugle, tête protubérante,
haute résistance, installation en tirant Luft- und Raumfahrt - Blindniet, Universalkopf, hochfest (Zugtyp) This European Standard was approved by CEN on 11 March 2016
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member
This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom
EUROPEAN COMMITTEE FOR STANDARDIZATION
C O M I T É E UR O P É E N DE N O R M A L I SA T I O N
E UR O P Ä I SC H E S KO M I T E E F ÜR N O R M UN G
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved
worldwide for CEN national Members Ref No EN 6129:2016 E
Trang 4Contents Page
European foreword 3
1 Scope 4
2 Normative references 4
3 Requirements 4
3.1 Configuration, dimensions and tolerances 4
3.2 Grip range and weight 4
3.3 Material, finish, lubrication 5
4 Designation 10
5 Marking 10
6 Technical specification 10
Trang 5BS EN 6129:2016
EN 6129:2016 (E)
3
European foreword
This document (EN 6129:2016) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN)
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn
at the latest by March 2017
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom
Trang 61 Scope
This standard specifies the configuration, dimension, tolerances and mass of a stainless steel blind bolt with protruding head, for aerospace application
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies
EN 2424, Aerospace series — Marking of aerospace products
EN 4473, Aerospace series — Aluminium pigmented coatings for fasteners — Technical specification1)
AS 5272, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting Procurement Specification2)
SAE AMS 5687, Nickel Alloy, Corrosion and Heat-Resistant, Wire 74Ni — 15,5Cr — 8,0Fe — Annealed2)
SAE AMS 5737, Steel, corrosion and heat-resistant, bars, wire, forgings and tubing 15Cr — 25.5Ni — 1.2Mo —
2.1Ti — 0.006B — 0.30V, consumable electrode melted, 1650 °F (899 °C), solution and precipitation heat treated2)
AMS-QQ-P-35, Passivation treatments for Corrosion-Resistant Steel2)
MIL-PRF-46010F, Lubricant, Solid Film, Heat cured, Corrosion Inhibiting NATO Code-S-17383)
SAE AS 87132, Lubricant, Cetyl Alcohol, 1- Hexadecanol, Application to fasteners3)
DOD-L-85645, Lubricant, Dry Thin Film, Molecular Bonded3)
NASM 8975, Fasteners, Blind, High Strength, Installation Formed, Corrosion Resistant Steel, Heat Resistant
Steel and Titanium, General Specification for4)
3.1 Configuration, dimensions and tolerances
The configuration, dimensions, tolerances, static and dynamic values shall conform to Figures 1 and 2 and Tables 1 and 2
3.2 Grip range and weight
See Tables 3 and 4
1) Published as AECMA Prestandard at the date of publication of this standard
2) Published by: Society of Automotive Engineers (SAE), 400 Commonwealth drive, Warrendale, PA 15096-0001, USA
3) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C 20301, USA
4) Published by: Aerospace Industries Association of America, Inc (AIA), 1250 Eye Street, N.W., Washington, D.C 20005-3924, USA
Trang 7BS EN 6129:2016
EN 6129:2016 (E)
5
3.3 Material, finish, lubrication
See Tables 5 and 6
Key
2 Sleeve shall not rotating 6 Locking collar
3 Diameter of serrated pin head shall not
exceed Ø D max 7 Shifting anvil: Fasteners are supplied with shifting anvil of manufacturer’s option The shifting anvil is
not part of the installed fastener
4 Serrated pin
Figure 1 — Configuration – Dimensions
Trang 8Key
1 Grip
2 Blind side head may be installed on 7° max slope
Figure 2 — Typical installation Table 1 — Dimensions and tolerances
Dimensions in mm (inch)
Diameter
code
⌀ A
Ref. Ø D Ø J N Q Ø D1 Ø D2 P a Ø P2
min max min max (±.001) ±0,03 (±.005) ±0,13 (±.010) ±0,25 (±.005)±0,13 max max max min
05 (.296) 7,52 (.328) 8,33 (.067) 1,70 (.077) 1,96 (.163) 4,14 (.375) 9,53 (.157) 3,99 (.067) 1,70 (.120) 3,05 (.085) 2,16 (.300) 7,62 (.216) 5,49
06 (.356) 9,04 (.394) 10,01 (.080) 2,03 (.090) 2,29 (.198) 5,03 (.375) 9,53 (.175) 4,45 (.087) 2,21 (.150) 3,81 (.110) 2,79 (.320) 8,13 (.27) 6,86
08 (.475) 12,07 (.525) 13,34 (.107) 2,72 (.117) 2,97 (.259) 6,58 (.375) 9,53 (.182) 4,62 (.110) 2,79 (.190) 4,83 (.144) 3,66 (.370) 9,40 (.35) 8,89
Diameter
code
Ref. Z J1 J2 X E C1
Ref. C2 F G Hole limits
max min (±.030) ±0,76 (±.030) max.±0,76 min. (±.002) ±5°±0,05 ±5° min max
05 (.010) 0,25 (.232) 5,84 (.844) 21,44 (.596) 15,14 (.587) 14,91 (.100) 2,54 (.005) 0,13 (.130) 3,30 (.032) 45° 30° 0,80 (.164) 4,17 (.167) 4,24
06 (.015) 0,38 (.292) 7,42 (.875) 22,23 (.615) 15,62 (.605) 15,37 (.130) 3,30 (.005) 0,13 (.130) 3,30 (.032) 45° 30° 0,80 (.199) 5,06 (.202) 5,13
08 (.020) 0,51 (.361) 9,17 (1.000) 25,40 (.725) 18,42 (.668) 16,97 (.150) 3,81 (.005) 0,13 (.130) 3,30 (.032) 45° 30° 0,80 (.260) 6,60 (.263) 6,68
a In the length P of Ø D may be 0,05 mm (.002) undersize
Trang 9BS EN 6129:2016
EN 6129:2016 (E)
7
Table 2 — Static values
Dimensions in kN (lbs)
Diameter code
Installed strength Single shear strength Tensile preload Tensile retention Spindle
05 (1980) 8,811 (1150) 5,117 0,512 (115) 2,558 (575)
06 13,016 (2925) (1690) 7,520 0,752 (169) 3,760 (845)
08 22,250 (5000) 12,905 (2900) (290) 1,29 (1440) 6,408
Table 3 — Grip range (1 von 2)
Dimensions in mm (inch)
Grip
length
code
Under lap Grip range Over lap Diameter code
only
05 dia
only
06 to
08 dia
05 to
08 dia
05 06 08
min min min max max Ref max Ref max Ref max
01 – – (.031) 0,79 (.096) 2,44 2,82 a
(.111) a 7,19
(.283) (.447) 11,35 – – – –
02 (.084) 2,13 (.078) 1,99 (.094) 2,39 (.0157) 3,99 (.173) 4,39 (.346) 8,79 12,95 (.51) (.373) 9,47 14,48 (.57) (.413) 10,49 16,76 (.66)
03 (.146) 3,71 (.14) 3,56 (.156) 3,96 (.220) 5,59 (.236) 5,99 (.408) 10,37 (14,53 (.572) (.435) 11,05 (.632) 16,05 (.475) 12,07 (.722) 18,34
04 (.209) 5,31 (.203) 5,16 (.219) 5,56 (.282) 7,16 (.298) 7,57 (.471) 11,97 (.635) 16,13 (.498) 12,65 (.695) 17,65 (.538) 13,67 (.785) 19,94
05 (.271) 6,88 (.265) 6,73 (.281) 7,14 (.345) 8,76 (.361) 9,17 (.533) 13,54 (.697) 17,70 (.560) 14,22 (.757) 19,23 15,24 (.6) (.847) 21,51
06 (.334) 8,48 (.328) 8,33 (.344) 8,74 (.407) 10,34 (.423) 10,74 (.596) 15,14 19,30 (.76) (.623) 15,82 20,83 (.82) (.663) 16,84 23,11 (.91)
07 (.396) 10,06 (.39) 9,91 (.406) 10,31 (.470) 11,94 (.486) 12,34 (.658) 16,71 (.822) 20,88 (.685) 17,40 (.882) 22,40 (.725) 18,42 (.972) 24,69
08 (.459) 11,66 (.453) 11,51 (.469) 11,91 (.532) 13,51 (.548) 13,92 18,29 (.72) (.884) 22,45 (.748) 19,00 (.945) 24,00 (.788) 20,02 (1.035) 26,29
09 (.521) 13,23 (.515) 13,08 (.531) 13,49 (.595) 15,11 (.611) 15,52 (.782) 19,86 (.946) 24,03 20,57 (.81) (1.007) 25,58 21,59 (.85) (1.097) 27,86
10 (.584) 14,83 (.578) 14.68 (.594) 15,09 (.657) 16,69 (.673) 17,09 (.845) 21,46 (1.009) 25,63 (.873) 22,17 (1.07) 27,18 (.913) 23,19 (1.16) 29,46
11 (.646) 16,41 16,26 (.64) (.656) 16,66 (.720) 18,29 (.736) 18,69 (.908) 23,06 (1.072) 27,23 (.936) 23,77 (1.133) 28,78 (.976) 24,79 (1.223) 31,06
12 (.709) 18,01 (.703) 17,86 (.719) 18,26 (.782) 19,86 (.798) 20,27 (.970) 24,64 (1.134) 28,80 (.998) 25,35 (1.195) 30,35 (1.038) 26,37 (1.285 32,64
13 (.771) 19,58 (.765) 19,43 (.781) 19,84 (.845) 21,46 (.861) 21,87 (1.033) 26,24 (1.197) 30,40 (1.061) 26,95 (1.258) 31,95 (1.101) 27,97 (1.348) 34,24
Trang 10Table 3 — Grip range (2 von 2)
Dimensions in mm (inch)
Grip
length
code
Under lap Grip range Over lap Diameter code
only
05 dia
only
06 to
08 dia
05 to
08 dia
05 06 08
min min min max max Ref max Ref max Ref max
14 21,184 (.834) (.828) 21,03 (.844) 21,44 (.907) 23,04 (.923) 23,44 (1.095) 27,81 (1.259) 31,98 (1.123) 28,52 (1.32) 33,53 (1.163) 29,54 (1.41) 35,81
15 (.896) 22,76 22,61 (.89) (.909) 23,01 (.970) 24,64 (.986) 25,04 (1.158) 29,41 (1.322) 33,58 (1.186) 30,12 (1.383) 35,13 (1.226) 31,14 (1.473) 37,41
16 (.959) 24,36 (.953) 24,21 (.969) 24,61 (1.032) 26,21 (1.049) 26,65 30,99 1.220 35,15 1.384 (1.248) 31,70 (1.445) 36,70 (1.288) 32,72 (1.535) 38,99
17 – (1.016) 25,81 (1.031) 26,19 (1.095) 27,81 (1.111) 28,22 – – (1.311) 33,30 (1.508) 38,30 (1.351) 34,32 (1.598) 40,59
18 – (1.078) 27,38 (1.094) 27,79 (1.157) 29,39 (1.173) 29,79 – – (1.373) 34,87 (1.570) 39,88 (1.413) 35,89 (1.660) 42,16
19 – (1.141) 28,98 (1.156) 29,36 (1.220) 30,99 (1.236) 31,39 – – (1.435) 36,45 (1.633) 41,48 (1.476) 37,49 (1.723) 43,76
20 – (1.203) 30,56 (1.219) 30,96 (1.282) 32,56 (1.298) 32,97 – – (1.498) 38,05 (1.695) 43,05 (1.538) 39,07 (1.785) 45,34
21 – (1.265) 32,13 (1.281) 32,54 (1.345) 34,16 (1.360) 34,54 – – (1.560) 39,62 (1.758) 44,65 (1.601) 40,67 (1.848) 46,94
22 – (1.328) 33,73 (1.344) 34,14 (1.407) 35,74 (1.423) 36,14 – – (1.623) 41,22 (1.820) 46,23 (1.663) 42,24 (1.910) 48,51
23 – (1.390) 35,31 (1.406) 35,71 (1.470) 37,34 (1.485) 37,72 – – (1.685) 42,80 (1.883) 47,83 (1.726) 43,84 (1.973) 50,11
24 – (1.453) 36,91 (1.469) 37,31 (1.532) 38,91 (1.548) 39,32 – – (1.748) 44,40 (1.945) 49,40 (1.788) 45,42 (2.035) 51,69
25 – (1.575) 40,01 (1.531) 38,89 (1.595) 40,51 (1.610) 40,89 – – (1.810) 45,97 (2.008) 51,00 (1.851) 47,02 (2.098) 53,29
a Only for 05 dia
Trang 11BS EN 6129:2016
EN 6129:2016 (E)
9
Table 4 — Weight
Weight in kg (lbs) /1000 parts
Grip length
code 05 Diameter code 06 08
02 (3.06) 1,39 (5.02) 2,28 (10.78) 4,89
03 (3.43) 1,56 (5.57) 2,53 (11.73) 5,32
04 (3.80) 1,72 (6.11) 2,77 (12.68) 5,75
05 (4.17) 1,89 (6.66) 3,02 (13.64) 6,19
06 (4.55) 2,06 (7.21) 3,27 (14.59) 6,62
07 (4.92) 2,23 (7.75) 3,52 (15.54) 7,05
08 (5.29) 2,40 (8.30) 3,77 (16.49) 7,48
09 (5.67) 2,57 (8.85) 4,01 (17.45) 7,92
10 (6.04) 2,74 (9.39) 4,26 (18.40) 8,35
11 (6.41) 2,91 (9.94) 4,51 (19.35) 8,78
12 (6.79) 3,08 (10.48) 4,75 (20.30) 9,21
13 (7.16) 3,25 (11.02) 5,00 (21.25) 9,64
14 (7.54) 3,42 (11.57) 5,25 (22.20) 10,07
15 (7.91) 3,59 (12.11) 5,49 (23.15) 10,50
16 – (12,65) 5,74 (24.10) 10,93
17 – (13.19) 5,98 (25.05) 11,36
18 – (13.73) 6,23 (26.00) 11,79
19 – (14.27) 6,47 (26.95) 12,22
20 – (14.81) 6,72 (27.90) 12,66
21 – (15.35) 6,96 (28.85) 13,09
22 – (15.89) 7,21 (29.80) 13,52
23 – (16.43) 7,45 (30.75) 13,95
24 – (16.97) 7,70 (31.70) 14,38
25 – (17.51) 7,94 (32.65) 14,81
Trang 12Table 5 — Material, finish, lubrication
Material/
Finish
code
Material Finish
Lubrication Sleeve Serrated pin Locking collar Sleeve Serrated pin Locking collar
C A-286 Cres per
AMS 5737
A-286 Cres per AMS 5737
A-286 Cres per AMS 5737;
316 Cres per AMS 5690
or Inconel per AMS 5687
See Table 6
Passivated per AMS-QQ-P-35
Passivated per AMS-QQ-P-35
a
None
a If lubricated, pin and/or collar shall be lubricated per AS5272 Type 1, MIL-L-46010 Type 1 or 3, MIL-L-87132 or DOD-L-85645
Table 6 — Sleeve finish codes
Code Material Finish
P
A-286-Cres Passivated per AMS-QQ-P-35
EXAMPLE
Marking as per EN 2424 style B on rivet head (EN Standard Number, grip length code and manufacturer’s identification required) Instead of the EN Standard Number, the manufacturer’s material code or part number shall be permissible
Single digit marking is permissible for grip length code less than 10
Shifting anvil and / or serrated pin shall be in red
See NASM 8975 except strength requirements as defined in Table 2