Instructions for IC CPD (waterfall light)

Microsoft Word Instructions for IC CPD Waterfall light IC CPD Instructions Standards IEC 62196 1 2014, IEC 62196 2 2014, IEC 61851 1 2017 IEC 62752 2016 Rated Voltage 220V AC（95 270 for North America.

IC-CPD Instructions

Standards IEC 62196-1 2014, IEC 62196-2 2014, IEC 61851-1 2017 IEC 62752 2016 Rated Voltage 220V AC（95-270 for North American market）

Rated Current 8A-10A-13A-16A/16A-25A-32A

Operating Freqyebcy 50Hz

Insulation Resistance ＞10MΩ

Level of Pretection IC-CPD IP67,Vehicle Connector IP54

Contact Resistance ≤0.5mΩ

Insection&Extraction

Operating

Storing Temperature -40℃～+80℃

Operating Humidity 5% ～95RH

weight 2.1kg

Thanks for using adjustable IC-PCD，please read instructions carefully before using the product in order to help you use the product correctly

Symbol： Caution

The symbol means: In the case of may or some extent endanger the safety of personal and property or damage the product facilities, give a reminder to avoid accidents

Symbol： Warning

The symbol means：In the case of seriously endangering personal and property safety

or damage to product facilities, prohibition instructions are given to avoid serious consequences

A、Parameters

B、Safety Informations

Caution

 The product should avoid to immerse in water as far as possible it should be above 0.75m away from the ground in charging

 Do not tramp, pull, bend, knot and other rough actions on vehicle connector and cable

 The product is a precision integrated circuit equipment, to avoid falling from high place, heavy objects hit pressure and other behaviors

 The minimum operating temperature of the product is -40℃

 The supply cable specification is 3*4mm2

 The surface label of this product is waterproof Please do not tear the label forcibly

Warning

 This product is only used in the environment with leakage protector at the supply end

 If the cable is damaged, do not use this product

 The product is only used for electric vehicles

 The product must be use in well grounded

 Do not use extra wire or switch plug in charging

 It is strictly prohibited to touch the internal conductive unit of the vehicle connector with fingers

 It is strictly prohibited to disassemble and repair

C、Caution

● Ensure the charging equipment, charging interface, cable, IC-CPD, wires and plug surface without damage, rust and other abnormal conditions before charging

● When the surface of the supply plug,vehicle connector, IC-CPD damp or stained, please wipe it with a dry and clean cloth under the condition of power failure to ensure that the product can be used normally

● Before charging, please make sure that the supply plug is consistent with the specification and model of the supply socket

● In charging status, the IC-CPD should be placed in a clean and tidy space to ensure that the cables are neatly and placed without folding or winding

● Do not use this product in the environment of corrosive liquid, flammable dust, flammable materials, etc

1、

1、First of all, make ture the gounding function of power soket is well done

2、To check whether the local voltage is consistent with the rated voltage

3、Plug into power supply,the LED will power on,the equipment start to self-inspection,it will be for 5 seconds.then you can see the charging interface

Self-inspection interface Charging interface

4、Current Setting

A When the blue waterfall light is on(not blinking),Long press function switch

3 seconds in charging interface.the function interface is on two options you

D、Charging Operation Steps

can see

Function interface Power option interface

B Short press function switch ,choose power option(the arrow is here )

C Long press function switch(3 seconds),the currents interface will be on

8A Current 16A Current

D Short press function switch,the current will be charged.choose the current

that you want(there are 4 options for 16A equipment;there are 3 options for 32A equipment)

E Long press function switch(3 seconds),the screen will be back to charging

interface.the current setting finished

F Insert the vehicle connector to vehicle inlet.the waterfall light turns blue to

green(blinking means charging,always on means charger finished) 5、Appointment charging Setting

A When the blue waterfall light is on(not blinking),Long press function switch

3 seconds in charging interface.the function interface is on two options you can see

Function interface Time option interface

B Short press function switch ,choose time option(the arrow is here )

C Long press function switch(3 seconds),the time interface will be on

No time setting Finished time setting

D Short press function switch, set the time that you want(one press one

hour,12 hours can be set)

F Stay the time interface on insert the vehicle connector to vehicle inlet.the

waterfall light turns blue to green.start to charge

Waterfall light Screen Vehicle connector status Status

R/G/B Blinking Self-inspection interface Disconnected Self-inspection

Blue on Function interface Disconnected Standby

Blue on

Function interface/setting

interface

Disconnected

Current setting Current setting Green blinking Function interface Connected Charging

Green on Function interface Connected Charger finished

E、Waterfall light and Screen status Description

Red on Earth Protection Connected Charging fault Red on Overvoltage Proteciton Connected Charging fault Red on Undervoltage Proteciton Connected Charging fault Red on Leak Protection Connected Charging fault Red on Overcurrent Protection Connected Charging fault Red on Overtemperature Protection Connected Charging fault

Red on Communication Failure Connected Charging fault

1， Product Length 5000mm

2， Power cable is 500mm long（From plug to function box）

3， Function box length,width,height:246.5*96*53.5mm

4， Vehicle Connector cable is 4500mm long（From Connector to box） 5， Packaging length,width,height:360*230*120mm

Serial Number

F、Dimension

G、Product Name and Quantity

1， The pruducts have passed strict inspection.The products have a one-year

warranty,except for quality problems caused for improper operation

2， The products because of the user's improper handling, installation, improper

use and maintenance, or due to natural disasters of the general product damage or scrap, are not within the scope of warranty

H、Warranty