Application of RadioOverFiber (ROF) in mobile communication

Application of Radio-Over-Fiber ROF in mobile communicationReza Abdolee, Razali Ngah, Vida Vakilian and Tharek A.Rahman Wireless Communication Centre Faculty of Electrical Engineering U

Application of Radio-Over-Fiber (ROF) in mobile communication

Reza Abdolee, Razali Ngah, Vida Vakilian and Tharek A.Rahman

Wireless Communication Centre Faculty of Electrical Engineering Universiti Teknologi Malaysia

81310 UTM Skudai Johor reza.ab@ieee.org, razalin@fke.utm.my, v.vakilian@gmail.com, and tharek@fke.utm.my

Abstract - Future generation of mobile

communication system must be capable of serving

high quality and broadband services even in highly

dense populated area The radio-over-fibre is one of

the promising systems which can be used along the

emerging wireless technologies such as smart

antenna or multiple input multiple output (MIMO)

systems to meet these requirements In this paper,

the role of ROF technology in next generation of

mobile communication system is presented, and

then the concept is clearly interpreted Then, base

on previous research and finding, a probable ROF

architecture for present and future wireless mobile

communication is portrayed Along this,

challenges and development issues of ROF

technology are presented as well

Keywords: ROF technology, CBS, RBS, WDM, DWDM

1 Introduction

Base on cellular concept to increase the

capacity of mobile cellular system cell optimization

can be used to take advantage of frequency reuse

scheme As a result of this scheme, the number of

base station increases in the area Increasing

number of base stations with current RF technology

especially in millimetre-wave band is very costly

And technically, using millimetre-wave band signal

is inevitable because the current RF spectrum is

limited Base on these facts, radio-over-fibre (ROF)

technology is a best choice to apply in cellular

system for cell optimization process since it can

easily be used in millimetre wave band and in

addition it can reduce the system overall cost [1]

ROF technology gives a lot of advantages such

as; The complicated signal processing is localized

at the central base station (CBS) therefore the

overall system is cost effective, remote base station

(RBS) is very simple, passive and compact

therefore it is transparent to air and its maintenance

is easy The system is very cost-effective because

of localization of signal processing in CBS and also

simple base station, the reliability of the system is high due to simple and passive structure of the RBS This system can easily serve high dense populated area such as shopping mall and airports, dead-zone area and highways can be covered efficiently and economically, the system can support multiple wireless standards [2] Because of high bandwidth nature of optical fiber, Broadband services are more feasible using this technology The centralized CBS can decrease the number of handover within the cells [2] Radiated power from antenna is very low due to Pico and Micro cells structure Low radiated power of antenna make the system more immune for human body and also reduces the power consumption of mobile battery The co-channel interference can greatly be reduced due to low radiation power In pico and micro cell structure, Propagation loss is less because of small cell radius These are some of the advantages of this system which make it attractive for future mobile communication system

The remained material of paper describes the ROF technology in 4G, probable future ROF architecture, ROF structure, ROF future trend and challenges, and at the end paper concludes

2 Role of ROF Technology In 4G The minimum bit rate that 4G would provide for broadband services is 20 Mb/s for indoor and 2 Mb/s for outdoor application even with high relative mobility Figure 1 shows the trend of mobile communication system [3] As candidate technologies for future systems, 4G-cellular and Intelligent Transport System (ITSs), have been attracting much interest in the mobile communication field [4] Both of these technologies take advantage of ROF technique The concept in 4G cellular system is cell optimization

In ITS system, the key technology in road vehicle communication system is again ROF, in which many base stations are equipped along the trunk road in order to communicate with vehicles, and several control base stations manage these base

1-4244-1435-0/07/$25.00©2007 IEEE

Figure 1: Trend of mobile communication

system

3 An Overview on ROF Mobile Technology

At Architecture Level

By using ROF technology, any type of radio

and millimetre wave signals can be transmitted

through optical fibres The structure of ROF system

in indoor and outdoor application is slightly

different Therefore, it should be explained in two

different sections

3.1 ROF Technology Structure in Indoor

Mobile Communication

In indoor communication and for frequency

below mm-wave, firstly, optical wave from a laser

diode (LD) is modulated directly by the radio

signal at the CBS and transmitted through the

optical fiber In remote base station (RBS), RF

modulated optical signal detected by photodiode is

transmitted into the wireless link by RBS antenna

However in indoor application three possible

structures can be considered to implement In the

first structure, RF signal usually in the range of 800 -

2200MHz is transmitted over single mode fibre,

second structure IF signal is transmitted over

multimode optical link and third structure the

signal is firstly digitized at CBS and then

transmitted over optical link This has the

advantages of digital transmission means that no

impairments due to noise and distortion but at the

expense of further complexity [5]

The most common of these architectures is the

first, RF over single mode fiber, because it is the

simplest to design and the lowest in cost

Consequently it put most stringent requirement on

the optical component It means that the system

needs the optical and electrical component which has a low noise and distortion in RF frequency The most dominant source of noise and distortion in ROF link is laser source Therefore by finding the suitable laser source which has right balance between cost and performance, the indoor ROF technology simply can be implemented

3.2 ROF Technology Structure for Outdoor Mobile Communication

In outdoor mobile communication, the frequency band which is considered for future mobile communication is in the range of 60 GHz known as mm-wave band frequency Direct modulation just functions for below mm-wave frequency [6], therefore for generating mm-wave frequency, external modulation or heterodyning techniques must be used In external modulation

RF signal and optical carrier are optical modulated using a Mach-zehnder modulator or an electro-absorption modulator The drawback of this system

is chromatic dispersion due to double-sideband transmission Therefore, the most popular technique can be heterodyning technique There are different structures for heterodyning modulation

In the first technique, two optical sources (DFB laser) in the operating range of 1550 nm as a master slave arrangement to produce RF signal are used in CBS This RF signal is modulated with the data The modulating RF signal can be detected by photodiode then it is transmitted by RBS antenna without any electrical mixer [7] The main drawback of this method is that it is not amendable

to all modulation format or modulation bandwidth and also chromatic dispersion is created in the signal because of mixing optical carriers with RF signal at the CBS

In the second structure, the RF carrier using two master slaves DFB is generated similar to first method However, in this technique data is not mixed with the RF signal and upconversion with the data is taken place in the RBS using conventional electrical mixer or in simpler arrangement using optoelectronic mixer Therefore, separate pair of laser source and photodiode is needed to transmit the data and carriers [6] Third technique is exactly the same as technique number two The only difference is in signal detection in the RBS where instead of photodiode an Electro Absorption Modulator (EAM) is used [6] This device can operate as a modulator in return path Therefore, the laser source in the RBS can be eliminated

3.3 Perspective of ROF Mobile

Communication

Integrated structure of indoor and outdoor ROF

mobile technology might have the structure which

portrayed in Figure-2 This system may use in the

future with some modification in topology For

example, RBS can be connected to central RBS

using BUS topology By applying this topology,

system cost is reduced by saving in applied optical

cable in the system As it can be seen from the

Figure-2 by using ROF repeater which is proposed

in [9] more than 300 base stations in cellular

system can be multiplexed by DWDM and

transmitted over SMF (Single Mode Fiber) to the

CBS In this structure, every base station uses one

single wavelength to connect to the CBS WDM or

DWDM is the core of this system In Every RBS,

single set of antennas can be used to receive

various RF signal in ITS communication [2] By

using ROF repeater, pre-existing FTTH fiber optic

can be used for 3G applications, even without any

change in EVM (Error Vector Magnitude) [9] One

of the components in Figure-2 is distributed

antenna system (DAS) which is used for indoor

communication and proposed in [3] DAS takes

advantage of optical switches which has a lot of

advantages in compared with RF switches High

level of isolation and very low cross talk are the

significant advantages

3.4 Remote Base Stations antenna (RBS)

Figure-3 shows the available Equipments in

RBS which can be listed as: one EAM

(Eletroabsorbtion modulator), one remote antenna,

diplexer, high power amplifier, low noise amplifier

and Power supply However, the trend of ROF

system is simplifying the RBS and changing it to

passive unit

Figure 3: The block diagram of remote base

station (RBS)

4 Future Trend of ROF Mobile Technology

Several issues for future ROF mobile

communication have to be addressed The first

issue is to simplify the RBS as much as possible The research direction aims to design passive RBS which is needed no maintenance and no service Compactness is another issue for RBS which is important in indoor mobile communication

To simplify the RBS a lot of researches have been done One solution is powerless RBS which is proposed in [9] Since this system can operate without electric power supply, it can be used in various situations In some researches the elimination of the optical source in the RBS using EAM [11], [6] is suggested In this method EAM act as a photodiode in downlink and operate as a modulator for the uplink Optical carrier which is need for the uplink is fed to the RBS from CBS remotely One of the proposed ideas in order to centralize the signal processing is predistortion in downlink and postdistortion in uplink to compensate the effect of laser and fiber nonlinearity [12]

One of the drawbacks of ROF system is costly CBS due to signal processing in RF frequency because of costly RF devices Therefore some researches are going on to substitute the electrical processing with optical one PDC (photonic down conversion) is the solution to eliminate the use of electrical RF component in the CBS [13] Using this technique the problem of chromatic dispersion

in the fiber also can be resolved [11],[13]

Another research direction in order to reduce the cost of ROF system is usage of Multi-Mode Fiber (MMF) instead of SMF Some researches have been done to use of pre-existing graded index fiber in the old urban area to reduce the cost [14] Also FFTH can be used by applying WDM In this structure proposed in [16] the use of OEO (Optical-Electrical-Optical) repeater and WDM for multiplexing different signal coming from different base station has been suggested In contrast, in new urban area which there is no communication infrastructure the system cost can be reduced by sharing the optical fiber from the RBS’s to CBS using Dense Wave Length Division Multiplexing (DWDM) over single mode fiber [15] By this technique 300 base stations can be connected to one CBS In indoor application to flexibility support the user and giving various services to the user the software controlled optical switch such as 3MEM has been proposed [3]

5 Some Challenges of ROF Technology

In order to design the ROF system with high transmission rate and high capacity to pervade in future mobile communication, there are a lot of technical problem which need to be resolved Some

of theses challenges are summarized in Table 2

Table-2: ROF challenges for mobile communication system

Challenges Some proposed solutions

Modulation technique, Direct modulation is exist just for below mm-wave frequency External

modulation, optical heterodyne technique and EAM modulator can be solutions

Chromatic dispersion Single Sideband Modulation (SSB) modulation, photonic downconversion

Phase distortion[1] 1.Phase noise cancellation method 2.Side band injection locking 3.error

correcting coding 4.Optical Phase Locked Loop (OPLL)

laser and optical fibre nonlinearity Pre-distortion and post-distortion technique [6]

Noise Characterization and

Cancellation for combination of

Optical and wireless noise

Characterize the optical-wireless noise by making relation between optical link property and optical devices with wireless noise

multi-user detection in Non linear

optical-wireless Estimation

Optical wireless detection using correlation property of PN code

RBS compactness and cost Centralizing the signal processing at CBS , elimination of laser source and

electrical mixer in RBS, Elimination of power supply in RBS,

High data rate wireless link as a

complimentary part of ROF

Using MIMO-OFDM-CDMA and smart antenna system

Expensive and complex uplink Using photonic down conversion, electrical signal processing can be done in IF

frequency(reduce the cost)

Non availability of Opto-electrical

interfaces

The researches are going on to provide a small size and low cost opto-electrical interfaces

Optical switch design 3DMEM technology with low price and all optical switches for ultra fast

switching

Figure 2: Perspective of ROF technology in mobile communication

6 Conclusion

In this paper, the application of ROF technology in

mobile communication is explained Recent finding

and issues in ROF mobile communication are

discussed The feature of future ROF technology in

mobile communication is presented Some of the

challenges are listed down Also the ROF

technology architecture for future mobile

communication system is portrayed

References

[1] Braun, R.P.; Grosskopf, G.; Rohde, D.”Optical

millimeter-wave generation and transmission

technologies for mobile communications, an

overview”Microwave Systems Conference, 1995

Conference Proceedings., IEEE NTC '95 17-19

May 1995 Page(s):239 – 242

[2] Tang, P.K.; Ong, L.C.; Luo, B.; Alphones, A.;

Fujise, M.; “Transmission of multiple wireless

standards over a radio-over-fiber network”

Microwave Symposium Digest, 2004 IEEE MTT-S

International Volume 3, 6-11 June 2004

Page(s):2051 - 2054 Vol.3

[3] M Fujise, K Sato and H Harada, “New

Road-Vehicle Communication Systems Based on Radio

on Fiber Technologies for Future Intelligent

Transport Systems (ITS),”Proc 1st Int’l Symp

Wireless Pers Multimedia Commun.,

Nov 1998, pp 139–44

[4]Shingo Ohmori, Yasushi Yamao and Nobuo

Nakajima,”The Future Generations of Mobile

Communications Based on Broadband Access

Technologies” IEEE Communications Magazine •

December 2000

[5] Wake, D.; Webster, M.; Wimpenny, G.;

Beacham, K.; Crawford, L.; “Radio over fiber for

mobile communications” Microwave Photonics,

2004 MWP'04 2004 IEEE International Topical

Meeting on 4-6 Oct 2004 Page(s):157 – 160

[6] Noel, L.; Wake, D.; Moodie, D.G.; Marcenac,

D.D.; Westbrook, L.D.; Nesset, D.;Novel

techniques for high-capacity 60-GHz fiber-radio

transmission systems Microwave Theory and

Techniques, IEEE Transactions on

Volume 45, Issue 8, Part 2, Aug 1997

Page(s):1416 – 1423

[7] L No¨el, D D Marcenac, and D Wake,

“Optical millimeter-wave generation technique

with high efficiency, purity and stability,” Electron Lett., vol 32, pp 1997–1998, 1996

[8] Nakajima, N.”ROF Technologies Applied for Cellular and Wireless Systems” Microwave Photonics, 2005 MWP 2005 International Topical Meeting on 12-14 Oct 2005 Page(s):, IEEE 2005,Conference Proceeding

[9] Stephen Z Pinter and Xavier N Fernando, Toronto, ON “Fiber Wireless Solution for Broadband Multimedia Access” IEEE Canadian Review - Summer 2005

[10] Kuri, T.; Kitayama, K.;”Novel photonic downconversion technique with optical frequency shift for millimeter-wave-band radio-on-fiber systems”Photonics Technology Letters, IEEE Volume 14, Issue 8, Aug 2002 Page(s):1163 –

1165

[11]X N Fernando and A B Sesay, “Higher Order Adaptive Filter Characterization of Microwave Fiber Optic Link Nonlinearity,” in Proceedings of SPIE - The International Society for Optical Engineering,vol 3927-06, January 2000,

pp 39-49

[12] N Takahashi, Y Ozeki, H Yokoyama, T Taguchi, M Kishi, and M Tsuchiya, “60 GHz-band fiber optic mm-wave uplink with chirp-inverted photonic downconversion scheme,” (in Japanese), , IEICE Tech Rep MWP2000-3, Oct

2000

[13] Kuri, T.; Toda, H.; Kitayama, K.;”Dense wavelength-division multiplexing millimeter-wave- band radio-on-fiber signal transmission with photonic downconversion” Volume 21, Issue 6, June 2003 Page(s):1510 – 1517,IEEE JNL [14] Kaoru Imai, Yukio Horiuchi and Noboru Edagawa” Radio-over-Fiber Distribution System with OEO Repeater for 3G Cellular Systems” Optical Society of America , OCIS codes: (060.2330) Fiber optics communications, 2005 [15] G L Stuber, J R Barry, S W Mclaughlin,

Y Li, M A Ingram, and T G Pratt, “Broadband MIMO-OFDM wireless communications,” Proceedings of IEEE, vol 92, no 2, pp 271-294, Feb 2004

[16] G J Foschini, G D Golden, P W Wolnianshy and R A Valenzuela, “ Simplified processing for high spectral efficiency wireless communication employing multi-element arrays,” IEEE Journal of Selected Areas in Communications, vol 17, no 11, pp 1841-1852, Nov 1999