Activity lab sc08 1
Lab 3.1.9c Rollover Cable Construction
... the cable ends • An RJ-45 to DB9 female terminal adapter, available from Cisco • Cabling continuity tester • Wire cutters Step Use the table as a reference to help create a rollover console cable ... Step 10 Test the finished cable Have the instructor check it How is it possible to tell if the cable is functioning properly? 3-3 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9c Copyri...
Ngày tải lên: 16/10/2013, 20:15
Lab 5.1.5 Troubleshooting Config Register Boot Problems
... the config- register to boot from NVRAM, save, and reload the router a Enter global configuration mode and enter the following commands: Router>enable GAD#configure terminal GAD (config) #config- register ... output shows a configuration register setting of 0x2142 This is the problem This configuration register setting is set to boot up in the password recovery mode This is why t...
Ngày tải lên: 16/10/2013, 20:15
Lab 3.1.9d Crossover Cable Construction
... end of the cable using the 568-A scheme to finish the crossover cable 3-4 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9d Copyright 2003, Cisco Systems, Inc Step 11 Test the finished cable Have ... Solid wire is fine for cable runs that are punched down into jacks Step Strip 5.08 cm (2in.) of jacket off one end of the cable 2-4 CCNA 1: Networking Basics v 3.0 - Lab 3.1.9d...
Ngày tải lên: 19/10/2013, 02:15
Lab 5.1.6 Hub and NIC Purchase
... should show the choices and the features or factors that were compared, such as number of ports, features, price, performance, and so on 2-2 CCNA 1: Networking Basics v 3.0 - Lab 5.1.6 Copyright
Ngày tải lên: 19/10/2013, 02:15
Lab 7.1.2 Waveform Decoding
... be downloaded Check with the instructor for help in obtaining the lab and waveform 2-2 CCNA 1: Networking Basics v 3.0 - Lab 7.1.2 Copyright 2003, Cisco Systems, Inc ... The lab can be downloaded from the local Academy server at the institution with Version 3.0 of the curriculum or from the Cisco Academy Connection website The Ethernet waveform for decoding
Ngày tải lên: 19/10/2013, 02:15
Lab 3.1.3 Configuring Router Passwords
... Enter The router is ready for the assigned lab to be performed 5-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright 2003, Cisco Systems, Inc Router Interface Summary Router Ethernet ... logoff by typing exit Turn the router off 4-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 3.1.3 Copyright 2003, Cisco Systems, Inc Erasing and reloading the router Ent...
Ngày tải lên: 23/10/2013, 00:15
Lab 5.1.10 Purchasing LAN Switches
... time allows, both of these That would often be the norm 2-2 CCNA 1: Networking Basics v 3.0 - Lab 5.1.10 Copyright 2003, Cisco Systems, Inc ... Start by going to www.cisco.com and selecting “Products & Services” and following the links to Switches to gather basic information Look specifically at the Catalyst 29xx and 35xx models Use ... The requirements include the following: • Replace...
Ngày tải lên: 23/10/2013, 00:15
Lab 7.1.9a Introduction to Fluke Network Inspector
... LAN is joined This lab introduces the Fluke Networks Network Inspector software, which may be useful in later troubleshooting labs and in the field While the Network Inspector software is a valuable ... the workstation, with Network Inspector or Protocol Expert installed, directly to a classroom switch or to a data jack connected to the school LAN Step Start Network I...
Ngày tải lên: 23/10/2013, 00:15
Lab Scenario 1
... $3600/mo for 24 months + $18 00/mo telco ( $11 9,396.94) Proposal $3000/mo + $18 0/mo for 24 months + $18 00/mo telco ( $11 0 ,11 0. 51) $3000/mo for 24 months + $3200 now ( $10 9,330. 61) Proposal $4300/mo for ... $265/mo for 24 months + $12 ,000 PBX replacement ( $11 2,934.63) $4300/mo for 24 mo + $4200 now + $12 ,000 PBX replacement ( $11 1,275.34) [IE-WANS-LS1-F03] [20 01- 06- 01- 01] Cop...
Ngày tải lên: 23/10/2013, 00:15