Plastics Materials 7E Episode 2 pps
Plastics Materials 7E Episode 2 pps
... (20 ) Bis-phenol polycarbonate (2 1) Poly(vinylcarbazo1e) (22 ) Nylon 6 (23 ) Nylon 66 (24 ) Poly(viny1 methyl ether) (25 ) Poly(viny1 isobutyl ether) (26 ) Poly(viny1 cyclohexanone) (27 ) ... (Figure 2. 22) Figure 2. 22 Further Consideration of Addition Polymerisation 3 1 the rate equation, where [SI is the concentration of transfer agent SH, is Vs = k,...
Ngày tải lên: 13/08/2014, 09:20
Plastics Materials 7E Episode 1 pps
... of ABS plastics 39 1 3 92 393 393 394 395 397 398 398 400 400 40 1 405 405 409 409 41 I 413 415 417 418 419 420 420 42 1 423 425 425 426 426 427 429 429 43 ... Bis-phenol A Polycarbonates Polyester Carbonates and Block Copolymers 2 1 21 .1 21 .2 21 .3 21 .4 21 .5 21 .6 21 .7 21 .8 21 .9 21 .10 Introduction Polyphenylenes Po...
Ngày tải lên: 13/08/2014, 09:20
Plastics Materials 7 Episode 5 ppsx
... CBY. 21 4 Polyethylene CH, f *CH,-CH CH2 / CHz \ CH, - CH * I I I /CH2 CH, *CH2 FH2 1 +C,H, - CH, - CH - (CH2)?- CH, I CH2 I CH,* Figure 10.1 / CH2 - / ... I., A.P.I. Project Theses 14. CLEGG, P. L. and HUCK, N. D., Plastics, 26 (28 2), 114 (1961); (28 3) 107 (1961) London, 2nd Edn., Chapter 8 (1960) Bibliography BOENIG, H. v. Polyolef...
Ngày tải lên: 13/08/2014, 09:20
Plastics Materials 7 Episode 6 ppsx
... impact (ft lbf/in-' notch) 0.95 0.95 0.3 4.0 24 .8 24 .8 70 30 25 5 25 5 400 20 4 0.8 0.96 0.96 0 .2 3.5 30.3 30.3 30 15 26 0 26 0 60 2 5 1.5 The linear low-density polyethylenes discussed ... Notched Izod @23 T Notched Izod @ -40°C Deflection temp @0.45MPa MPa % % GPa Jlm JIm "C 1 .22 -1 .24 60 25 300 140 27 180 1.7 1. 425 70 15 45 8...
Ngày tải lên: 13/08/2014, 09:20
Plastics Materials 7 Episode 16 ppsx
... 21 5, 29 9 crystallisation, SO, 67 density, 21 5, 22 0 electrical properties, 163, 20 7, 22 4, 22 6, 24 1 fillers, 22 8, 22 9 flow properties, 22 2 glass transition temperature, 62, 21 2 grades, ... grades, 21 3 high-density (HDPE), 8, 20 6-7, 21 1, 24 3-4, high molecular weight, 21 2, 23 8 light stability, 93 limitations, 24 1 linear low-density (LLDPE)...
Ngày tải lên: 13/08/2014, 09:20
High Cycle Fatigue: A Mechanics of Materials Perspective part 2 pps
... J.A., Failure of Materials in Mechanical Design: Analysis, Prediction, Prevention, Second Edition, John Wiley & Sons, New York, 1993. † Suresh, S., Fatigue of Materials, 2nd ed., Cambridge ... publications on the subject of fatigue [2] . The extensive review by Schütz is recommended reading for anyone with an interest in the history of the subject. 1 .2. WHAT IS HIGH CYCLE FATIGUE? A n...
Ngày tải lên: 03/07/2014, 20:20