Process Planning Episode 5 potx
Process Planning Episode 5 potx
... Figure 5. 14 Typical bench drill (Swift and Booker, 1997) 184 Process Planning Abrasive processes The main use for abrasive processes is improving the surface finish of previously processed ... or Production equipment and tooling selection 1 85 Figure 5. 19 Honing process and equipment (Swift and Booker, 1997) Figure 5. 20 Lapping processes and equipment (Swift and Booke...
Ngày tải lên: 12/08/2014, 16:21
Liquid Process Piping Episode 5 pdf
... (5. 5) 1 .52 (5. 0) 200 (8) 3. 35 (11.0) 3.20 (10 .5) 3. 05 (10.0) 2.74 (9.0) 1.83 (6.0) 1.68 (5. 5) 250 (10) 3 .51 (11 .5) 3. 35 (11.0) 3.20 (10 .5) 2.90 (9 .5) 1.98 (6 .5) 1.83 (6.0) 300 (12) 3.81 (12 .5) ... 1.07 (3 .5) 80 (3) 2.44 (8.0) 2.44 (8.0) 2.29 (7 .5) 2.13 (7.0) 1.37 (4 .5) 1.22 (4.0) 100 (4) 2 59 (8 .5) 2 59 (8 .5) 2 59 (8 .5) 2.29 (7 .5) 1 .52 (5. 0) 1.37 (4 .5) 150 (6...
Ngày tải lên: 12/08/2014, 16:20
Liquid Process Piping Episode 8 potx
... (- 250 EF to 600EF) Inconel 600 - 156 EC to 649EC (- 250 EF to 1,200EF) Inconel 6 25 - 156 EC to 649EC (- 250 EF to 1,200EF) Monel 400 - 156 EC to 815EC (- 250 EF to 1 ,50 0EF) Incoloy 800 - 156 EC to 815EC (- 250 EF ... to 1 ,50 0EF) 321 Stainless Steel -185EC to 815EC (-300EF to 1 ,50 0EF) 347 Stainless Steel -185EC to 815EC (-300EF to 1 ,50 0EF) Aluminum -198EC to 204EC (-325EF to 400EF)...
Ngày tải lên: 12/08/2014, 16:20
Process Planning Episode 1 pot
... Acknowledgements xi 5. 14, 5. 19, 5. 20, 5. 22, 5. 23, 5. 26 -5. 32. Reproduced from Process Selection - From Design to Manufacture by K.G. Swift and J.D. Booker. Figures 5. 12, 5. 13 and 5. 18. Reproduced ... adapted from Case Studies in Engineering Design by C. Matthews. Figures 4.7, 5. 1, 5. 2, 5. 4, 5. 8 -5. 11, 24 Process Planning -4, Figure 1.14 Saw Press Pa...
Ngày tải lên: 12/08/2014, 16:21
Process Planning Episode 3 pdf
... pitch (mm) M1.6 0. 35 0.2 M2 0.4 0. 25 M2 .5 0. 45 0. 35 M3 0 .5 0. 35 M4 0.7 0 .5 M5 0.8 0 .5 M8 1. 25 1.0 M10 1 .5 1. 25 M12 1. 75 1. 25 M16 2.0 1 .5 M20 2 .5 1 .5 M24 3.0 2.0 M30 3 .5 2.0 3.8 Screw ... 0100 H8/f7 (f) 01 25 Hll/cll (b) 050 H7/k6 (g) 0 75 H7/n6 (c) 080 H7/h6 (h) ~2 25 H7/g6 (d) 0 150 H8/f7 (i) 0 75 H7/n6 (e) 0 25 H7/p6 (j) 0 15 n9/e...
Ngày tải lên: 12/08/2014, 16:21
Process Planning Episode 11 pptx
... < 050 50 0 3000 150 0 250 0 <0600 <0300 +__0.1 0.4-6.3 ___0. 05 0.2-3.2 _0.1 1.0- 25 ___0 .5 1.6- 25 +__0. 05 0.2-12 .5 4 .5 6 3 3.7 6.3 50 -2000rpm 60-3000 rpm 60-600 rpm 50 - 750 rpm ... +__0.1 0.4- 25 ___0. 05 0.4- 25 ___0.0 05 0.4-6.3 __.0.0 05 0.0 25- 6.3 ___0.0 05 0.0 25- 6.3 ___0.0 05 0.0 25- 6.3 long 10 12 .5 4.2 3 4 20 18...
Ngày tải lên: 12/08/2014, 16:21
numerical mathematics and scientific computation volume 1 Episode 5 potx
... h1" alt=""
Ngày tải lên: 13/08/2014, 05:21