Standard Handbook of Engineering Calculations Episode 7 pot

... 25.4 74 4 .7 975 72 7.4 45 13 .7 9 × 5 × 10 22.9 × 12 .7 × 25.4 92 5.8 1210 902 .7 45 13 .7 10 × 6 × 12 25.4 × 15.2 × 30.5 141 8.9 1860 13 87. 6 48 14.6 12 × 7 × 12 30.5 × 17. 8 × 30.5 192 12.1 2530 18 87. 4 ... H s /77 8e, where t = temperature rise during shutoff, ºF; e = pump efficiency, expressed as a decimal; H s = shutoff head, ft. For this pump, t = (1 − 0. 17) (3200)/ [77 8(...

Ngày tải lên: 12/08/2014, 07:22

... 29.8–1,342.3 16 40.6 0.08–2. 97 59 .7 2,214 .7 12 30.5 0.22–5. 87 164.1–4, 377 .3 10 25.4 0. 37 8.29 275 .9–6,181.9 8 20.3 † 0.66–11 .71 492.2–8 ,73 2.1 ‡ 0.49–9. 07 365.4–6 ,76 3.5 6 15.2 § 1.44–19.15 1, 073 .8–14,280.2 † 1.15–15.91 ... spiral miter 18 45 .7 0. 07 0 .70 0.053–0.522 0.04–0.42 0.030–0.313 12 30.5 0.15–1.96 0.112–1.462 0.09–1. 17 0.0 67 0. 873 10 25.4 0.50–4.53 0. 373 –3...

Ngày tải lên: 12/08/2014, 07:22

... pumping temperature of 350°F ( 177 °C), and one of 75 hp (55.9 kW) with a pumping temperature of 150°F (66°C). Also housed in the room is a 1000-hp (74 5.6-kW) compressor and a 50-hp ( 37. 3-kW) compressor. Calculation ... percent. ENVIRONMENTAL ENGINEERING 7. 47 FIGURE 28 Ventilation system for effective removal of plant heat loads. (Chemical Engineering. ) Downloaded from Digi...

Ngày tải lên: 12/08/2014, 07:23

... 16–18 6.8 7. 6 20–26 8.5–11.0 50–90 393.3 70 7.9 8–11 62.9–86.5 0.50 1.3 12–15 5.1–6.4 17 22 7. 2–9.3 90–125 70 7.9–983.2 10–13 78 .7 102.3 1 2.5 8–12 3.4–5.1 14–18 5.9 7. 6 130–200 1023–1 573 13–16 ... tool has a setup standard time of 9 min and a unit standard time of 5.0 min, how many pieces must be handled if a machine with a setup standard of 60 min and a unit standard t...

Ngày tải lên: 12/08/2014, 07:22

... plane of bending. Evaluating gives F e ′=149,000(5.23) 2 /240 2 = 70 .76 kips/in 2 (4 87. 890 MPa); f a /F e ′=10.26 /70 .76 = 0145. Substituting in the first requirements equation yields 0 .76 7 + (0 .79 3/0.855)(5.35/22) ... 22(25,800)/[24 .75 (12)] = 1911 ft·kips (2591.3 kN·m). 6. Calculate the horizontal shear flow to be resisted. Here Q of flange = 13.88(23. 17) + 7. 0(24.50) − 0....

Ngày tải lên: 27/06/2014, 05:20

... 140 T6,T63,T6351 125 70 49 T73 295 70 50 T736 240 70 75 T6,T651 160 71 75 T66 160 T736 160 74 75 T7351 220 Table 209. FATIGUE STRENGTH OF W ROUGHT ALUMINUM ALLOYS (SHEET 4 OF 4) Alloy AA No. Temper Fatigue ... Mechanical Page 72 1 Wednesday, December 31, 1969 17: 00 ©2001 CRC Press LLC Shackelford & Alexander Mechanical Properties 71 7 70 75 0 60 T6,T651 150 71 75 T66 150 T7...

Ngày tải lên: 13/08/2014, 16:21