LEGO MINDSTORMS - The Unofficial Guide to Robots - Jonathan B Knudsen Part 7 pps

... BEGIN body UNTIL T pressed (using some stu BUTTON_INIT : waitForViewButton BEGIN RCX_BUTTON DUP BUTTON_GET @ 2 AND UNTIL ; In cu RCX_BUTTON nt state of the < /b> buttons into the < /b> RCX_BUTTON ... changes to < /b> B This word places the < /b> curren ca the < /b> values shown in Table Table 6-4 < /b> . BUTTON_GET Return Values Button Name Value R V P F H...

Ngày tải lên: 10/08/2014, 04:22

... how to < /b> use VB to < /b> talk to < /b> the < /b> RCX, and even includes several sets of instructions for building robots < /b> that you then program with VB. Bot-Kit http://www.object-arts.com/Bower/Bot-Kit/Bot-Kit.htm Bot-Kit, ... take control of the < /b> robot. If the < /b> robot drives over the < /b> edge of t auses the < /b> avoid behavior to < /b> assert itself. Fin...

Ngày tải lên: 10/08/2014, 04:22

... attaching the < /b> bumper touch sensors to < /b> input 1 and input 3. Slide the < /b> blue rubber bands onto the < /b> bumpers and anchor them to < /b> the < /b> bushings from the < /b> last step. he rubbT er bands keep the < /b> bumpers ... random order. Browsing the < /b> MINDSTORMS < /b> web ring is a good way to < /b> acquaint yourself with the < /b> MINDSTORMS < /b> onli...

Ngày tải lên: 10/08/2014, 04:22

... a wire brick to < /b> attach the < /b> right motor (the < /b> drive motor) to < /b> ou ng tput C. 96 90 Grabber Arm In Step 17, the < /b> half-bushings go between the < /b> center block and the < /b> cams (pear-shaped ... Wait(TURNAROUND_TIME); . All they o is run the < /b> arm motor in one direction until the < /b> limit sensor is pressed. Running the < /b> motor...

Ngày tải lên: 10/08/2014, 04:22

... 2 MOTOR_ 7 2 2 MOTOR_SET : spin stop 7 : : armGrab 7 1 0 MOTOR_SET ; : armRelease 7 2 0 MOTOR_SET ; : armStop 7 3 0 MOTOR_SET ; : grab mGrab ar BEG armRelease BEGIN 2 sensorValue ... that can be picked up or not. We begin by pushing the < /b> current nning total on to < /b> the < /b> stack. To < /b> begin with, the < /b> total is zero: hen we just run in a loop...

Ngày tải lên: 10/08/2014, 04:22

... four buttons. Use the < /b> following macros to < /b> interpret the < /b> state button BUTTON_ONOFF, BUTTON_RUN, BUTTON_VIEW, and BUTTON_PROGRAM. For e of the < /b> View button: ate(), BUTTON_VIEW)) { To < /b> te ... 198 The < /b> rotation sensor code does not work in the < /b> March 30, 1999 build of legOS 0.1 .7 irect-button.h) nitions to < /b> describe the < /b> s...

Ngày tải lên: 10/08/2014, 04:22

... soldered to < /b> the < /b> screws into the < /b> holes in the < /b> top of the < /b> brick. Now turn the < /b> screws into the < /b> brick— they should thread nicely into the < /b> holes. 5. Now you're ready to < /b> mount your sensor in the < /b> brick ... for the < /b> leads of the < /b> photoresistor. Then the < /b> leads were threaded through to < /b> the < /b> in...

Ngày tải lên: 10/08/2014, 04:22