Engineering Tribology Episode 1 Part 10 potx
Engineering Tribology Episode 1 Part 10 potx
... 94 -10 0. 57 B. Bhushan and K. Tonder, Roughness-Induced Shear- and Squeeze-Film Effects in Magnetic Recording, Parts 1 and 2, Transactions ASME, Journal of Tribology, Vol. 11 1, 19 89, Part 1, pp. ... ‘M v,i,j ’ i.e.: + ( ( R L 2 2C 1 + 2C 2 + F i,j M v,i,j = C 1 ( ( M v,i +1, j + M v,i 1, j C 2 ( ( M v,i,j +1 + M v,i,j 1 − G i,j (5.9) TEAM LRN 216 ENGINEERING TRIBOLOGY...
Ngày tải lên: 05/08/2014, 09:19
Process Engineering Equipment Handbook Episode 1 Part 10 potx
... .2 .15 .15 .1 .05 Epicyclic .15 .1 .1 .1 .1 .05 Steam turbines .25 .2 .15 .15 .1 .05 Gas turbines/axial compressors .5 .4 .25 .25 .1 .05 Pumps .25 .2 .15 .15 .1 .05 Motors .25 .2 .15 .15 LP1 LP2 ... Shutdown 20 Machine Type 1 2 3 4 VP1 VP2 GMF1 GMF2 BP1 BP2 Blowers (6000 rpm max) .5 .4 .25 .25 .1 .05 Horizontal centrifugal compressors .25 .2 .15 .15 .1 .05 Barrel compressor .15 ....
Ngày tải lên: 21/07/2014, 16:22
Engineering Mechanics - Statics Episode 1 Part 10 potx
... the publisher. Engineering Mechanics - Statics Chapter 5 Given: W 850 lb= a 0.5 ft= b 1ft= c 1. 5 ft= θ 1 10 deg= θ 2 30 deg= θ 3 10 deg= Solution: Guesses F A 1lb= F B 1lb= F C 1lb= Given Σ M B ... publisher. Engineering Mechanics - Statics Chapter 5 Units Used: kN 10 3 N= Given: F 500 N= a 0 .15 m= L 3m= Solution: The initial guesses w 1 1 kN m = w 2 1 kN m = Given + ↑ Σ...
Ngày tải lên: 21/07/2014, 17:20
Engineering Analysis with Ansys Software Episode 1 Part 10 potx
... X Y Z 10 −0.6e−3 2 8.3e−3 −2 .15 e−3 3 8.3e−3 1. 4e−3 4 13 .5e−3 1. 4e−3 5 13 .5e−3 1. 4e−3 6 8.3e−3 1. 4e−3 7 8.3e−3 2 .15 e−3 8 0 0.6e−3 9 8.3e−3 −0.8e−3 10 10 .5e−3 −0.8e−3 11 10 .5e−3 0.8e−3 12 8.3e−3 ... 24 /11 /2006 17 : 47 page 17 3 4.3 Mode analysis of a suspension for Hard-disc drive 17 3 Table 4.2 Keypoint numbers for making areas of a suspension Area No. Keypoint n...
Ngày tải lên: 06/08/2014, 11:21
Engineering Tribology Episode 1 Part 3 pdf
... 61. 2 68 74.8 ISO VG 10 0 90.0 10 0 11 0 ISO VG 15 0 13 5 15 0 16 5 ISO VG 220 19 8 220 242 ISO VG 320 288 320 352 ISO VG 460 414 460 506 ISO VG 680 612 680 748 ISO VG 10 00 900 10 00 11 00 ISO VG 15 00 13 50 ... 000 35 40 45 50 60 70 80 90 2 2.5 3 3.5 4 4.5 5 6 7 8 9 10 15 20 25 30 35 40 45 50 60 70 80 90 1. 9 1. 8 1. 7 1. 6 1. 5 1. 4 1. 3 1. 2 25 30 35 40 45 50...
Ngày tải lên: 05/08/2014, 09:19
Engineering Tribology Episode 1 Part 4 doc
... very high temper- atures ethers Perfluoro- polyethers Lubricants [J/kgK] 1. 3 − 13 .3 10 -3 1. 3 10 -4 1. 3 10 -4 1. 3 10 -4 1. 3 10 -5 ×6.67 10 -5 1. 3 10 -6 1. 3 10 -9 ×4 non- corrosive non- corrosive non- corrosive non- corrosive non- corrosive non- corrosive acts ... 440 40°C 19 13 15 11 12 ...
Ngày tải lên: 05/08/2014, 09:19
Engineering Tribology Episode 1 Part 5 doc
... 3.0 C 10 .1 D 22.5 Apparent viscosity [P] 10 -2 10 -1 10 0 10 1 10 2 10 3 10 4 10 5 10 6 Shear rate [s ] -1 FIGURE 3 .13 Non-Newtonian behaviour of calcium soap based greases ... region present FIGURE 3 .12 Temperature-life limits for typical greases [27]. 10 0 10 1 10 2 10 3 10 4 10 5 B A C D Soap con...
Ngày tải lên: 05/08/2014, 09:19